三辊卷板机校准和运输

  三辊卷板机归类于机械类在运输当中我们一定要多多关心，在卷板机运输时必须高度小心，只能并且一定要装在封闭的卡车内或有盖帘的“开顶”集装箱内运输，不能够暴露于灰尘，雨雾或烟气当中。   The three roller bending machine, belonging to the machinery in the transport of we must pay much attention to. In bending machine transport must be extremely careful, can and must be installed in the enclosed truck or cover curtain "truncated" container transport, shall not be exposed to the dust, rain and fog or smoke.   1.机器必须放在厚木板上并且必须安放稳定（通常情况下，卡车底座形态优良是可能的），装载时必须将机器主机架安放在卡车底座上。   1 the machine must be placed on a thick board and must be placed in a smooth (usually, the base of the truck is in good condition), and the machine must be placed on the base of the truck when it is loaded.   2.例如果机器是合为一体的，不要把所有东西放在机器上头、靠在上头或与机器的所有部分触及，机器必须放在卡车内的自由地段内。   2 if the machine is in one place, do not put anything in the machine above, on or in contact with any part of the machine, the machine must be placed within the free area of the truck.   3.机器的底座必须牢靠坚固，并紧紧地锚系住，防止在运输活动期间有所有搬运。在运输全过程当中尽可能免于急转弯、急刹车或猛烈地动动等。   The 3 machines must be firm and strong, tied firmly anchor, to prevent any movement during transportation. As far as possible in the transport process to avoid sharp turns, sudden brake or strong vibration, etc..   4.对于遥控装备，因其装有非常容易损害的电气喝电子器件，搬运或运输时要特别小心。   4 for the remote control device, because it is equipped with a very easy to damage the electrical and electronic devices, mobile or transport to be particularly careful.   当我们装好三辊卷板机时校准是不可缺氨赡，普通来讲校准的方法为。拧紧螺栓，必须时用填隙片放在螺栓下边调配平衡。用叉车或千斤顶只从承重梁两边或承重梁自身的背面提及起机器进行校平，不要靠到机器的其他所有部分。   When we installed three roller bending machine calibration is indispensable, general calibration method. Tighten the bolts, when necessary shim on the bolt below regulation level. Use a forklift or a jack only from the side of the bearing beam or bearing beam itself behind the lifting of the machine for school level, do not rely on any other parts of the machine.   1.机器必须用精密的平衡仪沿两个轴向校平：   1 the machine must be made with a precision level gauge with two axes:   2.两个机架：检查他们彼此是不是完全同相，为了完全同相，必须时运用填隙片（这是准确运用机器的必须前提）。   2. The two frame: check their whether or not each other completely in phase, to completely in phase, when necessary use shims (this is necessary conditions for the proper use of the machine).   3.在上压辊的纵轴：将平衡仪放在上压辊的正中央，在马达箱/卡轭方向上   The vertical axis 3 on the pressure roller: level and put it in the middle of the upper pressure roller, the motor yoke box / card direction   4.在侧压辊的横向上：将平衡仪放在两个压辊的两段靠近各个机架   4 in the lateral side roller on the level gauge on the two roller two near each rack   例如上就是三辊卷板机的校准方法喝卷板机运输的关心事点希望对大家有所帮助。   The above is the three roller machine calibration method and machine transport considerations and I hope to help you.